![]() |
We reproduce RUST REPAIR JEEP BODY PARTS and BODY PANELS which include FLOOR PANS, SIDE PANELS, FLOOR SUPPORTS & WHEELHOUSES. We also have WILLYS stamped WINSHIELD PANELS, CJ2 & CJ3 HEAVY DUTY BUMPERS & much more for 1941-1995 JEEPS including MB-CJ2A-3A-3B-M38-CJ5-M38A-CJ7-YJ-48-51 JEEPSTER, 46-62 WAGONS & PICKUPS and CJ8 SCRAMBLER. We are licensed to stamp WILLYS, JEEP and DODGE into our various products by CHRYSLER LLC. All of our products are MADE IN THE USA. |
Greetings Jeep people
We hope that our products will be of interest to you & likewise hope that your project goes well. LaMonte - Classic Enterprises |
BE SURE TO SELECT YOUR VEHICLE TYPE WHEN BROWSING FOR PARTS!
Coming Soon
Our new panels are intended for a fast and inexpensive front fender repair. Each panel is an overlay which can be pop-riveted, bonded, or welded into place over your original rusted fender. The wheel area lip is rolled inward like the original. Call for prices and availability (715-537-5422) |
New Products
Our new hood is an exceptional product intended to fill a specific custom or severe-use need. Produced in 16-gauge steel which is heavier than the original. The product is made in one piece which eliminates the center seam. All is properly edged and reinforced and includes the hood hinge as well.
HOOD OPTIONS SHOWN BELOW |
CJ2 Type WILLYS stamped sides as shown at right: $495.00 per hood |
![]() |
WILLYS silhouette cut out for back lighting shown at right: $520.00 per hood |
![]() |
No stamping or cut-outs for CJ3A or M38 types: $450.00 per hood |
![]() |
Large WILLYS stamping (1 1/2" high by 12" wide) across front of hood as shown at the right: $60.00 per stamping |
![]() |
MB, CJ2, 3, M38, EARLY CJ5, and M38A Wheel Flare Area Repair Panel Properly gauged steel - 2 1/4" exposed face with a flanged edge for a flush fit for welding. Yes, the wheel side edge is properly rolled inward as was original. |
![]() |
1941-1964 CJ2A, 3A, 3B, M38 Front Side Panel Cowl Reinforcement (A very nicely done reproduction)
Jeep
|
![]() |
Front Floor Support Joiner Made for MB and CJ2 types with driveshaft drum emergency brake. Properly die formed for an overlapping fit. SHOWN UPSIDE-DOWN FOR ILLUSTRATIVE PURPOSES $35 each |
![]() |
Passenger Side Wheelhouse Baffel and Corner Reinforcement. Properly gauged and die formed.
|
![]() |
CJ2 Internal Wheelhouse Channel Support for Driver Side
Jeep |
|
|
Front Fender End Caps for all 87-95 CJ Types. Made of top quality rust & dent proof fiberglass. $55.00 each as an introductory offer until the first 50 units are sold. |
REAR FRAME CROSS MEMBER Rear Face Shown Above Top View Shown Above Bottom View Shown Above '76-86 Rear Frame Cross Member. Perfectly detail cut & formed in original gauge steel. |
Jeep Stamped Side Panel Repair Clips
|
|
![]() |
|
|
|
|
|
r |
|
76-'95 CJ5-CJ7-YJ,Wrangler and CJ8 Scrambler Jeep Stamped Side Panel Repair Clips are now available as shown. Note that the upper edge of our panel is flanged to allow for a flush fit when clamping against your cut along the driver and passenger side entrances. The Jeep stamped lettering is exact in accordance to our original sample panel and approved by Chrysler LLC. The forward, upper, rear and lower edges of our panel are a duplication of the original. MADE IN THE USA in 18 gauge steel. Scroll down to appropriate JEEP type for more products. |
|
|
JEEP Stamped Cowl Area Repair Clip (17 1/4" High X 12" Wide) Introductory offer at $55.00 each Top, front & bottom edges are formed like the original panel. Rear edge is flanged to form a flush fit during installation. |
Jeep Taillights
Spice up that Jeep with tail lights that are sure to be noticed. Each taillight panel has one red lens, one amber lens, and one back-up light lens along with chrome finish perimeter bezel as shown above in photo A. Application - any Jeep with a flat rear panel. Bezel dimensions - 5 5/8" wide x 14 3/4" tall. Attachment screws included. Introductory sale price $105.00 per side plus our standard shipping rate. More custom products soon. |
Choose Your Vehicle
|
All products are Made in the USA with American muscle & American steel by Classic Enterprises |
All body components are of top quality construction and produced in our own facility with the exception of a limited inventory of original factory products of the same type. All components are made of original gauge steel with the exception of some parts which are made heavier than the original. We do not produce or have an inventory of parts other than what is shown here. Specify driver or passenger side when ordering.
Floor Panels Floor panels in 18 gauge steel. $85 each $125 each |
Floor Panels Driver side shown Driver short clip and full length panel shown above. (Passenger sides available). Please note that all Wagon/Pickup full length floor panels are shipped "flat" in order to meet Fed-X size requirements. The toe board area must be bent to shape by the installer noting the 2 notches and 2 punch marks per panel. All panels are die formed in 18 gauge steel as was original with extra material provided on the inboard side for use if needed. Steering Column and Pedal cutouts are as shown. You will have to adjust or modify if your original Floor Panel is different. WILLYS JEEP |
|
Floor Supports
Floor supports die formed in 16 gauge steel. A=Top $55.00 each B=Bottom $30.00 each
|
Box Floors for Jeep Pickups Stamped as shown in 16 gauge steel as was original. Not of original Jeep stamped corrugation but much better than flat steel or wood as a replacement. Made in 2 pieces overlapping at the center. (Same as Studebaker). Length measurement required by telephone or e-mail. (715-537-5422 or Lamonte@ClassicEnt.com)
Jeep |
![]() |
Pricing Information-Click here for Ordering/Shipping Info ![]()
| Wagon & Pickup '46-'63 | |
| Floor panels |
|
| Short panel | $85 each ![]() |
| Full length panel | $125 each |
| Front pillar floor support (A) | |
| Rear channel support (B) | |
| Box floors (16 gauge steel with 1" up-turned edge) |
$450 each |
|
Add 20% shipping to all orders under $150.00 and 10% to all orders of $150.00 or more for all lower 48 states domestic orders. Personal or company checks are accepted, as are VISA, MasterCard, American Express and Discover. Most orders are shipped via UPS. For all UPS domestic C.O.D. orders add 20% to the total. Non-domestic, Alaskan and/or Hawaiian orders can not be placed on line via our shopping cart. You will not be able to use the cart because the shipping charges on the cart are based on continental US shipping costs. We are unable to predict specific shipping cost for non-domestic order and are thus unable to quote shipping estimates. Such orders will be shipped at actual cost plus 5% of the value of the order for special handling. You must place your order via Master/Visa/Discover or American Express by Mail, Fax, E-mail or phone (715-537-5422). Sorry, checks or their equivalent can not be accepted. Be sure to include your telephone number and e-mail address (if available). Include your carefully recorded card number with the proper expiration date and the three digit code from the back of the card, or four digit code from the front of the American Express card. (Because of language problems we prefer that you submit your order via mail, fax or e-mail.) Click here for order form for fax or mail orders. Note that non-USA customers placing orders to be shipped to a USA address may not be able to order on line and may have to mail, fax, e-mail or telephone their order to us. Such orders will be shipped to a continental USA address at our standard shipping rates. Call or order anytime, including weekends; someone is usually in the office. Any product may be returned for a full refund within 30 days of receipt. Refund does not include shipping costs. WE HOPE THAT YOUR PROJECT GOES WELL-CLASSIC ENTERPRISES
|
|
||||||||
![]() |
Floor panels Full length drivers side shown. Properly die formed in 18 gauge steel. (26" maximum width.) Very nice reproduction. Passenger side available. Note that the Jeepster full length floor panels are shipped "flat" in order to meet Fed-X size requirements. The toe board area must be bent to shape by the installer noting the 2 notches and 2 punch marks per panel. All panels are die formed in 18 gauge steel as was original with extra material provided on the inboard side for use if needed. Steering Column and Pedal cutouts are as shown. You will have to adjust or modify if your original Floor Panel is different. Outboard rear of floor panel must be cut, elevated, and a wedge shaped patch of sheet metal must be added to match the original look of the floor (or simply save the same area of your original floor if appropriate). Short clip see price information to order
|
Pricing Information-Click here for Ordering/Shipping Info ![]()
| Jeepster '48-'51 |
|
| Floor panels (Shipped Fed Ex ) |
$245 each ![]() |
| Set of 2 | $475 set![]() |
| Short clip | $160 each ![]() |
| Set of 2 | $310 set ![]() |
|
Add 20% shipping to all orders under $150.00 and 10% to all orders of $150.00 or more for all lower 48 states domestic orders. Personal or company checks are accepted, as are VISA, MasterCard, American Express and Discover. Most orders are shipped via UPS. For all UPS domestic C.O.D. orders add 20% to the total. Non-domestic, Alaskan and/or Hawaiian orders can not be placed on line via our shopping cart. You will not be able to use the cart because the shipping charges on the cart are based on continental US shipping costs. We are unable to predict specific shipping cost for non-domestic order and are thus unable to quote shipping estimates. Such orders will be shipped at actual cost plus 5% of the value of the order for special handling. You must place your order via Master/Visa/Discover or American Express by Mail, Fax, E-mail or phone (715-537-5422). Sorry, checks or their equivalent can not be accepted. Be sure to include your telephone number and e-mail address (if available). Include your carefully recorded card number with the proper expiration date and the three digit code from the back of the card, or four digit code from the front of the American Express card. (Because of language problems we prefer that you submit your order via mail, fax or e-mail.) Click here for order form for fax or mail orders. Note that non-USA customers placing orders to be shipped to a USA address may not be able to order on line and may have to mail, fax, e-mail or telephone their order to us. Such orders will be shipped to a continental USA address at our standard shipping rates. Call or order anytime, including weekends; someone is usually in the office. Any product may be returned for a full refund within 30 days of receipt. Refund does not include shipping costs. WE HOPE THAT YOUR PROJECT GOES WELL-CLASSIC ENTERPRISES
|
|
||||||||
1941-1964 MB, CJ2A, 3A, 3B & M38
1941-1964 CJ2A, 3A, 3B, M38 Front Side Panel Cowl Reinforcement (A very nicely done reproduction)
Jeep
|
![]() |
New Product
|
|
WILLYS stamped patch panel in original 18 gauge steel Same lettering and scale as originally stamped into CJ2A windshield panel. Hood stamping patch and military WILLYS end panel patch is available upon special request.(Panel size 6" x 8 1/4") $35 each |
|||
| NOT FOR WIMPS FRONT BUMPERS (Shown Below) |
|||
Jeep Front Bumper CJ2-'45-'48 Top quality bumper for your Jeep. Pre-punched and over-gauged heavy duty. (Tooling modified for improved fit.) $95 each |
|||
Jeep Front Bumper CJ3A-'49-'52, CJ3B-'49-'64, M38-'51-'52 Top quality bumper for your Jeep. Pre-punched and over-gauged heavy duty. (Tooling modified for improved fit.) $95 each |
|||
Our new hood is an exceptional product intended to fill a specific custom or severe-use need. Produced in 16-gauge steel which is heavier than the original. The product is made in one piece which eliminates the center seam. All is properly edged and reinforced and includes the hood hinge as well.
OPTIONS SHOWN BELOW |
|||
CJ2 Type WILLYS stamped sides as shown at right: $495.00 per hood |
![]() |
||
WILLYS silhouette cut out for back lighting shown at right: $520.00 per hood |
![]() |
||
No stamping or cut-outs for CJ3A or M38 types: $450.00 per hood |
![]() |
||
Large WILLYS stamping (1 1/2" high by 12" wide) across front of hood as shown at the right: $60.00 per stamping |
![]() |
||
Front Fender angle supports Front fender angle supports for all flat fender types. |
Jeep |
||
Passenger Side $45 each |
|
||
Windshield Panels for MB and CJ2A $75.00 each |
|||
Die stamped WILLYS for all CJ2A types. (Approved by Chrysler LLC) $150.00 each |
|||
1941-1964 CJ2A, 3A, 3B, M38 A. Front floor panels
Jeep |
![]() |
||
J. Step tread
![]() |
![]() |
||
1941-1964 CJ2A, 3A, 3B, M38
Front Side Panel (A) Our original patterns & tooling have been adjusted for an improved fit. Made in 18 gauge steel. |
|||
1941-1964 CJ2A, 3A, 3B, M38 Front Side Panel Cowl Reinforcement (A very nicely done reproduction)
Jeep
|
![]() |
||
| Front & Rear Side Panel Joiner Gusset MB, CJ2A, CJ3A, CJ3B & M3
$ |
|
||
Rear Quarter Side Panel (B)
|
|||
MB, CJ2, 3, M38, EARLY CJ5, and M38A Wheel Flare Area Repair Panel Properly gauged steel - 2 1/4" exposed face with a flanged edge for a flush fit for welding. Yes, the wheel side edge is properly rolled inward as was original. |
![]() |
||
MB, CJ2A, CJ3A, M38 & CJ3B Lower Side Repair Strip Formed in #18 gauge steel. Flanged upper edge allows for a flush fit for welding purposes. Bottom of panel and wheel arch area are properly formed like original. Exposed face surface 4" high. |
|
||
|
|
SEAT BACK-CJ2A, CJ3A & CJ3B Two ribbed Military Panel also available. $35 |
||
SEAT BASE-CJ2A, CJ3A, CJ3B & Military Driver Side $35 |
SEAT BASE-CJ2A, CJ3A, CJ3B (Driver & Passenger Side) & Military Passenger Side |
||
1941-1976 CJ2A, 3A, 3B, M38 Toolbox forward and inboard face repair panels. Patterns are now adjusted for an improved fit.
|
Forward Toolbox Face |
||
Inboard Toolbox Face |
|||
Jeep |
|||
* Note-The installer will have to cut out the gas tank sump area on the driver floor panel if he wishes to use a Military gas tank. The driver floor support will likewise need to be modified for the same purpose. The installer will have to drill all appropriate holes in the floor panels as desired. |
|||
Driver Front Floor Panel
|
Passenger Front Floor Panel ![]() |
||
; Driver Front Floor Support![]() |
Passenger Front Floor Support![]() |
||
Front Floor Support Joiner Made for 1941-1964 MB, CJ2, CJ3 and M38 with driveshaft drum emergency brake Made for MB and CJ2 types with driveshaft drum emergency brake. Properly die formed for an overlapping fit. SHOWN UPSIDE-DOWN FOR ILLUSTRATIVE PURPOSES $35 each |
![]() |
||
Rear Floor Riser |
|||
1941-1975 CJ2A, 3A, 3B, CJ5, M38, M38A A. Tail light panel
Jeep |
![]() |
||
D. Tailgate Opening Surround Properly gauged and redesigned for a proper fit. NOW WITH CHAIN HOOK EYES ATTACHED.
$95 each |
|||
B. CJ2, CJ3 and M38 Rear Floor Panel with floor supports attached. (A very nicely done reproduction in 18 gauge steel with over gauged supports)
|
|
||
I. Tail Light Panel Properly die formed in 18 gauge steel as was original. Yes, all edges are properly formed as was original. Panels are not drilled or punched which allows the installer various tail light placement options. |
|
||
H. Tail Light Panel Rear Body Angle Support Produced in heavy 14 gauge steel |
![]() |
||
Tail Light Panel With Support Attached Properly die formed in 18 gauge steel as was original. Yes, all edges are properly formed as was original. Panels are not drilled or punched which allows the installer various tail light placement options. |
|
||
1941-1964 CJ2A, 3A, 3B, M38 Rear Valence Panel |
|||
New Product Rear Valence Angle Support. Produced in original gauge steel. |
![]() |
||
1941-1964 CJ2A, 3A, 3B, M38 Rear Valence Panel & Angle Supports as a unit |
|||
|
|||
Wheelhouses Nicely formed in #18 gauge steel as was original. Choose from two styles below. ----------------------- CJ2A '46-'49 ----------------------- CJ3A, CJ3B & M38 |
|
Passenger Side Wheelhouse Baffel and Corner Reinforcement. Properly gauged and die formed. |
![]() |
CJ2 Internal Wheelhouse Channel Support for Driver Side
|
|
CJ2 External Wheelhouse Angle Support Connects & reinforces area between leading face of Wheelhouse & inboard face of side panel |
![]() |
CJ3 & later External Wheel-house Angle Support Connects & reinforces area between leading face of Wheelhouse & inboard face of side panel |
![]() |
1941-1975 End Panels for Military & Custom Types. (Eliminates tail light panels & tail gate.) All structural bracing & hardware attached to our panels via appropriate spot welds. Spot welds cosmetically covered for our photographic & display purposes. |
Jeep
|
WILLYS stamped Military or Custom end panel $750 each
|
|
Unstamped Military or Custom end panel $425 each |
|
(Back side shown at right) Jeep |
![]() |
Rear Frame Crossmember & Stiffener Insert-Die formed & properly gauged & punched. (Can be used on later models if re-drilled to suit the application). |
|
Pricing Information-Click here for Ordering/Shipping Info ![]()
| Early type MB, CJ2A, 3A, 3B, M38 ('41-'64) | |
| Front bumper, original gauge steel, all holes punched | |
| Hood (No Stamping) | $450 each ![]() |
| Hood with WILLYS stamped sides | $495 each ![]() |
| Hood with WILLYS stencil silhouette cut-outs | $520 each ![]() |
| Large WILLYS stamped across front of any hood above | $60 each ![]() |
| Front fender angle support Driver Side | |
Front fender angle support Passenger Side |
$35 each ![]() |
| Windshield panel for MB Military | |
| WILLYS stamped windshield panel for CJ2A | |
| Forward tool box face | |
| Inboard tool box face | |
| Step treads | |
| Lower body repair strip 4" high | |
| Front side panel (Includes step tread) | |
| Front side panel cowl area reinforcement | $60 each ![]() |
| Side panel Joiner Gusset | $15 each ![]() |
| Rear 1/4 side panel | |
| All 4 side panels | |
| Wheel flare area repair panel | $85 each ![]() |
| Front floor panels | |
| Front floor supports | |
| Front floor support joiner for MB and CJ2 types | $35 each ![]() |
Seat back CJ2A, CJ3A, CJ3B & Military |
$35 each |
| Seat base panel-Military Passenger& Civilian Passenger & Driver Sides |
|
Seat base panels - Military Driver Side Only |
$35 each ![]() |
| Rear floor riser | |
| Rear floor panels with supports attached | |
| Rear floor shock mount housing (not shown) | |
| Wheelhouse support baffel and corner reinforcement for passenger side | $105 each ![]() |
| Wheelhouse reinforcement channel for drivers side | $45 each ![]() |
| Rear wheelhouses CJ2A '46-'49 | |
| Rear wheelhouses CJ3A, CJ3B & M38 | $185 each ![]() |
| Wheelhouse external angle support, CJ2 Only | |
| Wheelhouse external angle support, CJ3 & Later | $25 each ![]() |
| Tail light panels | $35 each ![]() |
| Taillight panel rear body angle support | $10 each ![]() |
| Taillight panel with rear body angle support attached | $55 each ![]() |
| Rear valence panel | |
| Rear valence angle support | $10 each ![]() |
| Rear valence panel & Angle Supports Attached | $75 each ![]() |
| Tailgate opening surround | |
| WILLYS stamped Military or Custom end panel | |
| Unstamped Military or Custom end panel | |
| WILLYS stamped patch panel - Same scale as windshield panels and tailgate stamping. (Panel size 6" x 8 1/4") |
|
| Rear frame crossmember '41-'48 |
|
Add 20% shipping to all orders under $150.00 and 10% to all orders of $150.00 or more for all lower 48 states domestic orders. Personal or company checks are accepted, as are VISA, MasterCard, American Express and Discover. Most orders are shipped via UPS. For all UPS domestic C.O.D. orders add 20% to the total. Non-domestic, Alaskan and/or Hawaiian orders can not be placed on line via our shopping cart. You will not be able to use the cart because the shipping charges on the cart are based on continental US shipping costs. We are unable to predict specific shipping cost for non-domestic order and are thus unable to quote shipping estimates. Such orders will be shipped at actual cost plus 5% of the value of the order for special handling. You must place your order via Master/Visa/Discover or American Express by Mail, Fax, E-mail or phone (715-537-5422). Sorry, checks or their equivalent can not be accepted. Be sure to include your telephone number and e-mail address (if available). Include your carefully recorded card number with the proper expiration date and the three digit code from the back of the card, or four digit code from the front of the American Express card. (Because of language problems we prefer that you submit your order via mail, fax or e-mail.) Click here for order form for fax or mail orders. Note that non-USA customers placing orders to be shipped to a USA address may not be able to order on line and may have to mail, fax, e-mail or telephone their order to us. Such orders will be shipped to a continental USA address at our standard shipping rates. Call or order anytime, including weekends; someone is usually in the office. Any product may be returned for a full refund within 30 days of receipt. Refund does not include shipping costs. WE HOPE THAT YOUR PROJECT GOES WELL-CLASSIC ENTERPRISES
|
|
||||||||
![]() |
|
CJ5 51-75 Jeep Stamped Side Panel Repair Clips are now available as shown. Note that the upper edge of our panel is flanged to allow for a flush fit when clamping against your cut along the driver and passenger side entrances. The Jeep stamped lettering is exact in accordance to our original sample panel and approved by Chrysler LLC. The forward, upper, rear and lower edges of our panel are a duplication of the original. MADE IN THE USA in 18 gauge American steel. It should be noted that the Jeep stamping as shown above & on the cowl clip below is not original to some 51 to 75 types but looks good anyway. Unstamped panels are available upon special request. |
|
![]() |
JEEP Stamped Cowl Area Repair Clip (17 1/4" High X 12" Wide) Introductory offer at $55.00 each Top, front & bottom edges are formed like the original panel. Rear edge is flanged to form a flush fit during installation.
|
1951-1975 CJ5, M38A1 A. Front floor panels
Jeep
|
|
||
*Note-The installer will have to cut out the gas tank sump area on the driver floor panel if he wishes to use a Military gas tank. The driver floor support will likewise need to be modified for the same purpose. The installer will have to drill all appropriate holes in the floor panels as desired. |
|||
Floor Panels- Early CJ5 ('51-'71) Driver side at right, passenger side at far right in original 18 gauge steel. (Toeboard to rear floor riser in length.) |
|
||
Floor Panels- Early CJ5 ('72,-'75) Driver side at right, passenger side at far right in original 18 gauge steel. (Toeboard to rear floor riser in length.) |
|
||
Floor Supports- Early CJ5 ('51-'71) Front Floor Supports Driver side at right, passenger side at far right in steel heavier than the original.
|
|
||
Floor Supports- Early CJ5 ('72-'75) Front Floor Supports Driver side at right, passenger side at far right in steel heavier than the original.
|
|
||
Front Floor Support Joiner CJ3, M38, Early CJ5 Types Made for later types not needing an emergency brake spring return retainer. SHOWN UPSIDE-DOWN FOR ILLUSTRATIVE PURPOSES $25 each |
![]() |
||
| Rear Floor Riser-Early CJ5 Die formed in steel heavier than the original with Frame Mounts attached. $85 each |
|||
Lower Side Repair Strip-CJ5 Formed in #18 gauge steel. Flanged upper edge allows for a flush fit for welding purposes. Bottom of panel and wheel arch area are properly formed like original. Exposed face surface 4" high. |
|
||
1951-1975 CJ5 and M38A Wheel Flare Area Repair Panel Properly gauged steel - 2 1/4" exposed face with a flanged edge for a flush fit for welding. Yes, the wheel side edge is properly rolled inward as was original. |
![]() |
1941-1975 End Panels for Military & Custom Types. (Eliminates tail light panels & tail gate.) All structural bracing & hardware attached to our panels via appropriate spot welds. Spot welds cosmetically covered for our photographic & display purposes. |
Jeep |
WILLYS stamped Military or Custom end panel |
|
Unstamped Military or Custom end panel |
|
(Back side shown at right) |
![]() |
1941-1975 CJ2A, 3A, 3B, CJ5, M38, M38A A. Tail light panel
|
![]() |
Properly gauged and redesigned for a proper fit. NOW WITH CHAIN HOOK EYES ATTACHED.
|
|
A. Tail Light Panel Properly die formed in 18 gauge steel as was original. Yes, all edges are properly formed as was original. Panels are not drilled or punched which allows the installer various tail light placement options.
|
|
Tail Light Panel Rear Body Angle Support
Produced in heavy 14 gauge steel |
![]() |
Tail Light Panel With Support Attached Properly die formed in 18 gauge steel as was original. Yes, all edges are properly formed as was original. Panels are not drilled or punched which allows the installer various tail light placement options.
Jeep |
![]() |
1951-1975 CJ5 AND M38A1 Rear Valence Panel |
|
New Product Rear Valence Angle Support Produced in original gauge steel. |
![]() |
1951-1975 CJ5 AND M38A1 Rear Valence Panel & Angle Supports as a unit |
|
Wheelhouse 1951-1975 CJ5, M38A Nicely formed in #18 gauge steel as was original. |
|
CJ5 External Wheelhouse Angle Support Connects & reinforces area between leading face of Wheelhouse & inboard face of side panel |
![]() |
Wheelhouse Support Baffle 1951-1975 CJ5, M38A Properly die formed and sold as shown. Dimensions are 11 1/2" x 12 1/4" |
![]() |
---WE HAVE AN ABUNDANCE OF NOS POSTAL JEEP REAR FLOORS--- CALL FOR PRICES (715) 537-5422 |
|
Rear Floor Panel for 51-75 CJ5 & CJ6 (M38A) |
|
Pricing Information-Click here for Ordering/Shipping Info ![]()
| CJ5 & M38A1 '51-'75 | |
| Front floor panels | |
| Front floor supports | |
| Front floor support joiner | $25 each ![]() |
| Lower body repair strip 4" high | |
Jeep stamped side panel repair clip 51-75 |
$145 each ![]() |
| Jeep stamped cowl panel clip | |
| Cowl area reinforcement | $60 each ![]() |
| Rear floor riser | |
| Rear floor panel with supports attached | |
| Rear wheelhouse | |
| Wheelhouse external angle support | |
| Rear wheelhouse support baffle with corner reinforcement for passenger side | |
| Rear valence panel | |
| Rear valence angle support | $10 each ![]() |
| Rear valence panel & Angle Supports Attached | $75 each ![]() |
| Tailgate opening surround | |
| Rear frame cross member '41-'48 | |
| Tail light panels | $35 each ![]() |
| Taillight panel rear body angle support | |
| Taillight panel with rear body angle support attached | $55 each ![]() |
| WILLYS stamped Military or Custom end panel | |
| Unstamped Military or Custom End panel | |
| 1951-1975 CJ5 and M38A Wheel Flare Area Repair Panel | $85 each ![]() |
| WILLYS stamped patch panel - Same scale as windshield panels and tailgate stamping. (Panel size 6" x 8 1/4") |
|
Add 20% shipping to all orders under $150.00 and 10% to all orders of $150.00 or more for all lower 48 states domestic orders. Personal or company checks are accepted, as are VISA, MasterCard, American Express and Discover. Most orders are shipped via UPS. For all UPS domestic C.O.D. orders add 20% to the total. Non-domestic, Alaskan and/or Hawaiian orders can not be placed on line via our shopping cart. You will not be able to use the cart because the shipping charges on the cart are based on continental US shipping costs. We are unable to predict specific shipping cost for non-domestic order and are thus unable to quote shipping estimates. Such orders will be shipped at actual cost plus 5% of the value of the order for special handling. You must place your order via Master/Visa/Discover or American Express by Mail, Fax, E-mail or phone (715-537-5422). Sorry, checks or their equivalent can not be accepted. Be sure to include your telephone number and e-mail address (if available). Include your carefully recorded card number with the proper expiration date and the three digit code from the back of the card, or four digit code from the front of the American Express card. (Because of language problems we prefer that you submit your order via mail, fax or e-mail.) Click here for order form for fax or mail orders. Note that non-USA customers placing orders to be shipped to a USA address may not be able to order on line and may have to mail, fax, e-mail or telephone their order to us. Such orders will be shipped to a continental USA address at our standard shipping rates. Call or order anytime, including weekends; someone is usually in the office. Any product may be returned for a full refund within 30 days of receipt. Refund does not include shipping costs. WE HOPE THAT YOUR PROJECT GOES WELL-CLASSIC ENTERPRISES
|
|
||||||||
1976-1995 CJ5, CJ7 and YJ Wrangler
Coming Soon
Our new panels are intended for a fast and inexpensive front fender repair. Each panel is an overlay which can be pop-riveted, bonded, or welded into place over your original rusted fender. The wheel area lip is rolled inward like the original. Call for prices and availability (715-537-5422) |
New Products
|
Front Fender End Caps for all 87-95 CJ Types. Made of top quality rust & dent proof fiberglass. $55.00 each as an introductory offer until the first 50 units are sold. |
REAR FRAME CROSS MEMBER v Rear Face Shown Above Top View Shown Above Bottom View Shown Above '76-'86 Rear Frame Cross Member. Perfectly detail cut & formed in original gauge steel. |
![]() |
|
CJ5 Jeep Stamped Side Panel Repair Clips are now available as shown. Note that the upper edge of our panel is flanged to allow for a flush fit when clamping against your cut along the driver and passenger side entrances. The Jeep stamped lettering is exact in accordance to our original sample panel and approved by Chrysler LLC. The forward, upper, rear and lower edges of our panel are a duplication of the original. MADE IN THE USA in 18 gauge American steel. |
|
CJ7 & YJ Wrangler Jeep Stamped Side Panel Repair Clips are now available as shown. Note that the upper edge of our panel is flanged to allow for a flush fit when clamping against your cut along the driver and passenger side entrances. The Jeep stamped lettering is exact in accordance to our original sample panel and approved by Chrysler LLC. The forward, upper, rear and lower edges of our panel are a duplication of the original. MADE IN THE USA in 18 gauge American steel. $155 each |
|
![]() |
JEEP Stamped Cowl Area Repair Clip (17 1/4" High X 12" Wide) Introductory offer at $55.00 each Top, front & bottom edges are formed like the original panel. Rear edge is flanged to form a flush fit during installation.
|
CJ5 Lower Side Repair Strip Formed in #18 gauge steel. Flanged upper edge allows for a flush fit for welding purposes. Bottom of panel and wheel arch area are properly formed like original. Exposed face surface 4" high. |
|
CJ7 & YJ Lower Side Repair Strip Formed in #18 gauge steel. Flanged upper edge allows for a flush fit for welding purposes. Bottom of panel and wheel arch area are properly formed like original. Exposed face surface 4" high. |
|
1976-1995 CJ5, CJ7, YJ
A. Floor panels and view of foot area clip
Jeep
|
'76-'95 Foot Area Repair Clips (17 1/2"Wide X 16"Long) 18 Gauge American Steel
Made in the USA with American muscle & American steel by Classic Enterprises |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
1976-95 CJ5, CJ7, CJ8 A. Toe board support All floor supports are properly die formed in steel heavier than the original.
Jeep
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||
Floor Panels
Jeep All panels are approx. 16" wide & die stamped in 18 gauge steel. Outside edge is rolled down as was original. Floor panels and inboard and outboard rails are made for CJ7 and CJ8 types and must be shortened for use on CJ5 types. The parts which you receive will look like the photographs shown on our web site.
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||
Front Body Supports Properly gauged with all captured nuts brought to original factory size & standard. A. Front toeboard support
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||
B. Front traverse support Front 3/4 view shown. Made in 2 pieces per vehicle in steel heavier than original. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
Inboard & Outboard Rail Supports Floor panels and inboard and outboard rails are made for CJ7 and CJ8 types and must be shortened for use on CJ5 types. The parts which you receive will look like the photographs shown on our web site. All supports are die formed in steel heavier than the original. (Captured nuts which were typical to all types are attached to all of our supports.) * Inboard and outboard rails are shipped as shown and will have to be shortened and slightly modified to fit on CJ5 Types. ----------------------------------------------- C. Longer front Inboard rail shown at center of photo. --------------------------------------- D. Shorter front outboard rail shown at far left & right of photo. |
Front Inboard & Outboard Rails |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Rear Floor Panel for 76-96 CJ5-CJ7-YJ Rear floor panels are available as shown which are original Jeep old stock panels which were sold as surplus rejects from the original Jeep plant in Toledo. We have attached our support channels as would have been done on original panels. All panels will be slightly stained and/or have some surface rust. Yes we know that the panels look terrible but also know that they will clean up nicely. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
'76-'95 CJ5, CJ6 Wheel Flare Area Repair Panel Properly gauged steel - 2 1/4" exposed face with a flanged edge for a flush fit for welding. Yes, the wheel side edge is properly rolled inward as was original. |
![]() |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
Wheelhouse '76-'95 CJ5, CJ7 & YJ Produced in original 18 gauge steel. |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||
Wheelhouse Support Baffle '76-'95 CJ5,CJ7 & YJ Nicely die formed panel. |
![]() |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
Tailgate End Support for all '76-'95 Types (Front & rear views shown) Now properly die formed with all captured nuts brought to original factory size & standard. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
REAR FRAME CROSS MEMBER v Rear Face Shown Above Top View Shown Above Bottom View Shown Above '76-'86 Rear Frame Cross Member. Perfectly detail cut & formed in original gauge steel. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
Pricing Information-Click here for Ordering/Shipping Info
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() |
Front Fender End Caps for all 87-95 CJ Types. Made of top quality rust & dent proof fiberglass. $55.00 each as an introductory offer until the first 50 units are sold. |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() |
JEEP Stamped Cowl Area Repair Clip (17 1/4" High X 12" Wide) Introductory offer at $55.00 each Top, front & bottom edges are formed like the original panel. Rear edge is flanged to form a flush fit during installation. |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
Scrambler CJ8 H. Front floor panels Very nice die formed reproduction in 18 gauge steel. |
![]() ![]() |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
Foot Area Repair Clips
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||
Lower Side Repair Strip Formed in #18 gauge steel. Flanged upper edge allows for a flush fit for welding purposes. Bottom of panel and wheel arch area are properly formed like original. Exposed face surface 6 1/2" high. |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||
SCRAMBLER A. Toe board support All floor supports are properly die formed in steel heavier than the original. Jeep |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||
Floor Panels
Jeep All panels are approx. 16" wide & die stamped in 18 gauge steel. Outside edge is rolled down as was original. Floor panels and inboard and outboard rails are made for CJ7 and CJ8 types and must be shortened for use on CJ5 types. The parts which you receive will look like the photographs shown on our web site. |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||
Front Body Support Properly gauged with all captured nuts brought to original factory size & standard. A. Front toeboard support |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||
B. Front traverse support Front 3/4 view shown. Made in 2 pieces per vehicle in steel heavier than original. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
Inboard & Outboard Rail Supports Floor panels and inboard and outboard rails are made for CJ7 and CJ8 types and must be shortened for use on CJ5 types. The parts which you receive will look like the photographs shown on our web site. All supports are die formed in steel heavier than the original. (Captured nuts which were typical to all types are attached to all of our supports.) C. Longer front Inboard rail shown at center of photo. ------------------------------------- D. Shorter front outboard rail shown at far left & right of photo. |
Front Inboard & Outboard Rail |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
| A. Front corner floor panel B. Rear corner floor panel C. Rear wheelhouse D. Rear floor panel (with 3 forward supports pre-attached) E. Rear floor riser F. Rear floor support G. Tailgate end support |
![]() |
||||
D. Rear floor panel (with 3 forward supports pre-attached) An exceptional product in 18 gauge steel as was original. The three main supports are spotwelded to the panel. All previous errors have been corrected. (The two final supports are available if needed, 715-537-5422) Shipped via FED-EX
|
![]() |
||||
Front of rear floor corner panels (Driver side at right and passenger side at far right.) Type A |
|
||||
Rear of rear floor corner panels (Driver side at right and passenger side at far right.) Type B |
|
||||
All 4 panels shown at right
|
|
||||
Wheelhouses (Fits either side) A very good quality Product. |
![]() |
||||
CJ8 Scrambler Rear Floor Support (1/4 Side & Bottom View Shown)
|
|||||
CJ8 Scrambler Tailgate End Support (Front & Rear Views Shown Below)
$165 each Now properly die formed with all captured nuts brought to |
|||||
REAR FRAME CROSS MEMBER R Rear Face Shown Above Top View Shown Above Bottom View Shown Above '76-'86 Rear Frame Cross Member. Perfectly detail cut & formed in original gauge steel. |
shown
Pricing Information-Click here for Ordering/Shipping Info ![]()
| Scrambler | |
| Front Fender End Caps | $55 each |
| Front floor panels: 16" wide | |
| Set of 2 | |
| Foot area repair clip | |
| Front supports: Toe board support (A) |
|
| Main traverse support, outside to center (B) | |
| Inboard rail (C) | |
| Outboard rail (D) | |
| Full set of 8 | |
| Wheelhouse | |
| Rear floor panels with 3 front supports attached (Shipped Fed Ex at a $50.00 flat fee.) |
|
| Front of rear floor corner panels (A) | $40 each ![]() |
| Rear of rear floor corner panels (B) | |
| Floor corner panels (all 4 corners) | $160 a set of 4 ![]() |
| Rear floor support | |
| Tailgate end support | |
| Lower side repair panel 6 1/2' high | |
Jeep stamped side panel repair clip |
$165 each![]() |
| Jeep stamped cowl repair clip | |
| Rear frame cross member | $105 each ![]() |
Be sure to specify driver or passenger side where appropriate when ordering.
|
Add 20% shipping to all orders under $150.00 and 10% to all orders of $150.00 or more for all lower 48 states domestic orders. Personal or company checks are accepted, as are VISA, MasterCard, American Express and Discover. Most orders are shipped via UPS. For all UPS domestic C.O.D. orders add 20% to the total. Non-domestic, Alaskan and/or Hawaiian orders can not be placed on line via our shopping cart. You will not be able to use the cart because the shipping charges on the cart are based on continental US shipping costs. We are unable to predict specific shipping cost for non-domestic order and are thus unable to quote shipping estimates. Such orders will be shipped at actual cost plus 5% of the value of the order for special handling. You must place your order via Master/Visa/Discover or American Express by Mail, Fax, E-mail or phone (715-537-5422). Sorry, checks or their equivalent can not be accepted. Be sure to include your telephone number and e-mail address (if available). Include your carefully recorded card number with the proper expiration date and the three digit code from the back of the card, or four digit code from the front of the American Express card. (Because of language problems we prefer that you submit your order via mail, fax or e-mail.) Click here for order form for fax or mail orders. Note that non-USA customers placing orders to be shipped to a USA address may not be able to order on line and may have to mail, fax, e-mail or telephone their order to us. Such orders will be shipped to a continental USA address at our standard shipping rates. Call or order anytime, including week ends; someone is usually in the office. Any product may be returned for a full refund within 30 days of receipt. Refund does not include shipping costs. WE HOPE THAT YOUR PROJECT GOES WELL-CLASSIC ENTERPRISES
|
|
||||||||

P.O. Box 92, Barron, WI 54812





















CJ5-7 panel shown directly above




































































































