Pre-Lark Post-War Sedans Coupes & Convertibles, '47-'52
Body panels and body parts for Studebaker vehicles

pricing below Click For Pricing Info
pricing below Click For Shipping Info
pricing below Click For Ordering Info

payment options

Pricing Information               

      Floor Panels, 47-52 Sedans, Coupes & Convertibles

             

                      Driver Side                                   Passenger Side

Produced in 18-gauge steel with close attention paid to indentation detail. Shipped as two pieces per side. Front sections may be ordered by special request. 23" width. Seat anchor plates are now attached.


    23" wide

$270 per side

     Both Sides
$520 per car

 

Master Cylinder Access Cover

(Can also be used as a gas tank sender unit cover)

$8 each

                  

Body Supports

Produced in steel heavier than the original. 3 body supports per side, which were originally spot-welded to the floor panels and bolted to the frame.

     Front
$65 each

     Middle
$55 each

     Rear
$65 each

     Set of 6
$350 set

Body Supports

Trunk Panel ('50-'52)

 

Accurately formed in heavy 18-gauge steel.

  $310 each

Spare Tire Wheel Well

A perfect reproduction in rust-proof fiberglass. (Companion to trunk panels.)

 

$175 each

 

      

SPARE TIRE HOLD DOWN WASHERS

47-64 SPARE TIRE HOLD DOWN WASHERS (6”DIA)

$15 each
add to cart

                    

Lower Door Skins

Approximately 5"H x full length. Forward and bottom edges rolled as original. Rear edge left open to allow for proper installation. Upper edge is flanged for a flush fit.

$45 each

Rocker Panels 1947-1952
Panels are properly curved and arched with die formed ends. Bolts are attached for 2-door types. Produced in original gauge steel.

    

2 Door shown-All 4 door types available.

(Choose options in shopping cart.)

 

$190 set (Driver/Passenger)

Rocker Panels     Vent Shrouds

Vent Patch & Hinge & Shroud Collar
Outer perimeter of vent patch is flanged for a flush fit during installation. Very good product in proper gauge steel. Vent patch or hinge & shroud collar can be ordered individually or as a unit. Vent patch revealed face dimensions are 7 1/2"W x 13 1/4"H. Perimeter edge is rolled for a flush fit during installation.

Vent Patch

 

 

 

$75 each

           

Hinge & Shroud Collar

 

 

$75 each

                     

Vent Patch & Hinge & Shroud

Collar as a unit

 

$160 each

         

Vent Shrouds
Our vent shrouds bridge the gap between the outer vent door area and the inner cowl vent area and also accepts the vent hose that attaches to the fan and under seat heater on the passenger side. Made in durable rust proof fiberglass.

Vent shrouds $160 per car
                    

top


Pricing Information

Sedans, Coupes & Convertibles '47-'52

(Specify driver or passenger side when ordering.)


     23" wide $270 per side

     both sides $520 per car

Master cylinder access cover $8 each

Body supports:
     Front $65 each

     Middle $55 each

     Rear $65 each

     Set of 6 $350 set

   
Trunk panels $310 each

Spare tire wheel well $175 each

Spare tire hold-down washer $15 each
       add to cart
Vent patch $75 each

Hinge and shroud collar $75 each

Vent area patch panel & hinge & shroud collar attached $160 each

Vent shrouds in fiberglass $160 per car

Lower Door Skins $45 each

Rocker Panels $190 set


top

Shipping Information

Add 10% shipping to all domestic orders. Personal or company checks are accepted, as are VISA, MasterCard, American Express and Discover. Most orders are shipped via UPS. For UPS C.O.D. orders add 15% to total.

Non-domestic, Alaskan and/or Hawaiian orders can not be placed on line via our shopping cart. You will not be able to use the cart because the shipping charges on the cart are based on continental US shipping costs. We are unable to predict specific shipping cost for non-domestic order and are thus unable to quote shipping estimates. Such orders will be shipped at actual cost plus 5% of the value of the order for special handling. You must place your order via Master/Visa/Discover or American Express by Mail, Fax, E-mail or phone (715-537-5422). Sorry, checks or their equivalent can not be accepted. Be sure to include your telephone number and e-mail address (if available). Include your carefully recorded card number with the proper expiration date and the three digit code from the back of the card, or four digit code from the front of the American Express card. (Because of language problems we prefer that you submit your order via mail, fax or e-mail.) Click here for order form for fax or mail orders. Note that non-USA customers placing orders to be shipped to a USA address may not be able to order on line and may have to mail, fax, e-mail or telephone their order to us. Such orders will be shipped to a continental USA address at our standard 10% shipping rate.

Call or order anytime, including weekends; someone is usually in the office. Any product may be returned for a full refund within 30 days of receipt. Refund does not include shipping costs.

WE HOPE THAT YOUR PROJECT GOES WELL-CLASSIC ENTERPRISES

 

How To Order

MAIL: Click here for order form for fax or mail orders.
PHONE: You may also call your order in.
ONLINE: To order online, simply click on the "Add to Cart" buttons above next to your desired product, and it will automatically redirect you to the shopping cart.

payment options