Frame rail repair sections for all '47-'66 Stude

 cars & Avanti.

 Pass the word around. Discounts will be allowed for advance orders as an   introductory offer. Give us a call or an e-mail 24/7 for more information 715-537-5422 lamonte@ClassicEnt.com

Floor Panels

Our Floor Panels are 22" wide and extend from the firewall seam to the rear seat riser in length. Our die stamped panel is manufactured in heavy 18 gauge steel and now includes the seat anchor plates pre-attached. Note that our Floor Panel thresholds are properly formed and are arched front to rear just like the original floor panel which will allow for proper Rocker Panel placement and the maintenance of original body shape and proper door fit upon completion.

Note also that we have paid close attention to original indent detail which is necessary for a proper repair or restoration. We have used original Studebaker archive prints in order to achieve a high degree of accuracy in our product. Pricing Information

$270 Driver side

3 pieces per side which includes

joiner strip as shown above.

$270 Passenger side

3 pieces per side which includes

joiner strip as shown above.

            Driver and Passenger Sides         
            6 pieces, (both sides) which includes joiner strips as shown above.

            $520 Per Car       

Master Cylinder Access Cover

(Can also be used as a gas tank sender unit cover)

         
$8 each

Body Supports

Each Lark has six frame-to-body supports. Our supports are accurately reproduced in steel heavier than the original. If your original supports are rusted or overstressed due to metal thinning, your Lark will be more flexible than necessary.

Body support-Front $70 ea

Body support-Middle $70 ea

Body support-Rear   $70 ea

Body supports, all 6 $410 set
                                       

Trunk Panels ('61-'66)

Produced in two pieces in 18-gauge steel, to facilitate frame-on installation. Main Trunk panels can be made to work on '53 to '60 types.

Note the black marked lines on our photo. You may cut and elevate our panel in that area as directed or cut the marked area out if not needed.

$320 each

Trunk Floor Corner Supports

Produced in steel, heavier than the original. As with C/K types, shim to adjust door fit.

$40 each

SPARE TIRE HOLD DOWN

WASHER

47-64 SPARE TIRE HOLD DOWN

WASHERS (6”DIA)

$15.00

Rear of Front Fender Patches

Produced in 18-gauge steel. Front edge is flanged to allow flush fit. Rear of panel is rolled, as was original. Full length by 5" wide.

Rocker Panels

Our rocker panels have pre-formed weatherstrip channels and are properly arched from front to rear just like the originals which will allow for the maintenance of proper body shape, proper door fit and general ease of installation. Made of original gauge steel. Bolts are attached to all two-door types as was original.

Rocker Panels 1959-1960     

2 Door shown-All 4 door types available.

(Choose options in shopping cart.)

$190 set (Driver/Passenger)

Rocker Panels 1961-1966

2 Door shown-All 4 door types available.

(Choose options in shopping cart.)

$190 set (Driver/Passenger)

Lower Door Skins

Approximately 5"H x full length. Forward and bottom edges rolled as original. Rear edge left open to allow for proper installation. Upper edge is flanged for a flush fit.

$45 each

Shipping Information

Add 10% shipping to all domestic orders. Personal or company checks are accepted, as are VISA, MasterCard, American Express and Discover. Most orders are shipped via UPS. For UPS C.O.D. orders add 15% to total.

Non-domestic, Alaskan and/or Hawaiian orders can not be placed on line via our shopping cart. You will not be able to use the cart because the shipping charges on the cart are based on continental US shipping costs. We are unable to predict specific shipping cost for non-domestic order and are thus unable to quote shipping estimates. Such orders will be shipped at actual cost plus 5% of the value of the order for special handling. You must place your order via Master/Visa/Discover or American Express by Mail, Fax, E-mail or phone (715-537-5422). Sorry, checks or their equivalent can not be accepted. Be sure to include your telephone number and e-mail address (if available). Include your carefully recorded card number with the proper expiration date and the three digit code from the back of the card, or four digit code from the front of the American Express card. (Because of language problems we prefer that you submit your order via mail, fax or e-mail.) Click here for order form for fax or mail orders. Note that non-USA customers placing orders to be shipped to a USA address may not be able to order on line and may have to mail, fax, e-mail or telephone their order to us. Such orders will be shipped to a continental USA address at our standard 10% shipping rate.

Call or order anytime, including weekends; someone is usually in the office. Any product may be returned for a full refund within 30 days of receipt. Refund does not include shipping costs.

WE HOPE THAT YOUR PROJECT GOES WELL-CLASSIC ENTERPRISES