|
Fits Jeep CJ7 and CJ8. The Floor Supports or Outboard Rail Supports are die formed in steel heavier than the original. Captured nuts which were typical to all types are attached to all of our supports ... more
|
|
18 Gauge Steel ... more
|
|
Extended width, full length floor panels, die stamped in properly gauged American draw quality steel. Spans the distance from the firewall seam to the rear floor riser as one continuous panel. It ... more
|
|
Jeep rear floor For 1976-1983 Jeep CJ5 1976-1986 Jeep CJ7 and 1987-1995 Jeep Wrangler YJ. ... more
|
|
A recreation of the original mount for the scissor jack that was located either under the driver's seat or under the hood on certain model year CJ5's and CJ7's. ... more
|
|
Jeep CJ5, CJ7 and CJ8 Rear Frame Cross Member. Perfectly detailed, cut with holes and die formed in original gauge steel. ... more
|
|
Fits CJ7, CJ8, and YJ ... more
|
|
Jeep Stamped Side Panel Repair Clips are produced from 18 gauge American steel. The Jeep stamped lettering is exact in accordance to our original sample panel and approved by Chrysler LLC. ... more
|
|
Side and bottom edges are bent at 90 o and the top is flanged for an easier installation. Approximately 6-1/4 inch height, plus a 1/2 inch flange, and is full width. ... more
|
|
The rear 1/4 has the rear 90 0 bend where it meets the corner and the upper edge is flanged so you can weld to your original tub edge. The wheel opening has the finished edge as it should. ... more
|
|
Supports are die formed in steel heavier than the original. Captured nuts which were typical to all types are attached to all of our supports. ... more
|
|
Our rear of front floor repair panel is for the area that rusts out under the roll bar mount and seat belt area. The outside edge is rolled down as was original. ... more
|
|
Bottom edge formed at 90° angle. Flanged upper edge for welding purposes. Rear is curved, then formed at 90º angle, to properly meet the tail light panel. Exposed surface approximately ... more
|
|
Our full width one piece traverse supports are properly gauged with all appropriate nut blocks and cages pre-attached as was original. Our one piece support can be installed without removing the body ... more
|
|
Our rear floor riser is made like the originals, properly gauged, die stamped and of very good quality. ... more
|
|
Our exhaust heat shield protects your rear floor panel from excessive muffler heat. It is reproduced in 18 gauge American steel by Classic Enterprises at our production facility here in the USA. ... more
|
|
Front 3/4 view shown. Made in 2 pieces per vehicle in steel heavier than original. ... more
|
|
Die formed with all captured nuts original factory size & standard. ... more
|
|
The iconic Jeep stamping, brought into your home, office, or garage! Built with the same die and gauge of steel as our CJ7 and YJ side panels. This is as close as you can get to putting a piece of a ... more
|
|
Our panel is formed in 18 gauge steel with a flanged upper edge that allows for a flush fit for welding purposes. The length of our panel begins with a 90 0 fold at the front fender seam and ... more
|
|
18 gauge steel ... more
|
|
Die stamped in 18 gauge steel. Outside edge is rolled down as was original. ... more
|
|
Our new 2 piece side repair kit includes the front quarter with the officially licensed "Jeep" stamped side repair, and the rear quarter side repair. They are designed to work together to form a ... more
|
|
Our new 2 piece side repair kit includes the front quarter with the officially licensed "Jeep" stamped side repair, and the rear quarter side repair. They are designed to work together to form a ... more
|
|
Our new 2 piece side repair kit includes the front quarter with the officially licensed "Jeep" stamped side repair, and the rear quarter side repair. They are designed to work together to form a ... more
|
|
Jeep Wheelhouse Support Baffel with the corner support attatched. Nicely die formed panel. ... more
|
|
Finally, a keychain for your Jeep. ... more
|