'76-'86 Jeep CJ7
_____Floor_____
___Front Area___
Side and Cowl Area
____Supports____
__Tail/Rear Area__
___Wheel Area___
_______All_______

2 Piece Side Repair
Our 2 piece side repair kit has our "Jeep" stamped side repair and now you can order our new rear 1/4 side repair.They are designed to work together to form a complete side repair.
The rear 1/4 (panel B) has the rear 900 bend where it meets the corner and the upper edge is flanged so you can weld to your original tub edge. The wheel opening has the finished edge as it should. Panel B is flanged where it meets panel A for a smooth fit.
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$150.00 Driver Rear 1/4 Side Repair Panel A
$155.00 Driver Front 1/4 Side Repair Panel B
$150.00 Pass Rear 1/4 Side Repair Panel A
$155.00 Pass Front 1/4 Side Repair Panel B
Full Length Front Floor Panels
Our extended width floor panels are available in properly gauged American draw quality steel. Our panels are accurately die stamped as a full length panel that spans the distance from the firewall seam to the rear floor riser as one continuous panel.
A one piece panel makes for fewer fitting and alignment problems and less welding and warpage during installation. The outside edges of our panels are folded down as was original. The inboard edges are folded properly upward to follow the transmission tunnel curvatures as shown in our photo.
We do not drill or punch any holes other than the two per panel as shown in the photos at the right. We have found that our customers prefer to drill their own according to their need and preference.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$180.00 Driver
$180.00 Passenger
$360.00 Pair
Economy Narrow Full Length Floor Panels
Outside edge is rolled down as was original. The length of our panel is from the firewall seam to the rear floor riser as one continuous panel.
- Approx. 13 inches wide
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$140.00 Driver
$140.00 Passenger
$270.00 Pair
Foot Area Repair Clips
Jeep Foot Area Repair Clips. Outside edge is rolled down as was original.
- Approx. 16 inches wide
- Die Formed
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Drivers
$55.00 Passenger
$110.00 Pair
Rear of Front Floor Repair
- Die Stamped
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Drivers
$55.00 Passenger
110.00 Pair
Toe Board Front Floor Body Supports
Comes with all captured nuts and studs attatched. Original factory size and standards.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$95.00 Driver
$95.00 Passenger
$190.00 Pair
Full Width One Piece Traverse Body Support
Our one piece support can be installed without removing the body from the frame although you may have to raise the body slightly on some types. Installation can be accomplished by rear drive shaft and/or exhause pipe removal in some instances. A one piece traverse support is sure to save you considerable cutting, alignment, welding time and alleviate a lot of general installation frustration as well.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$175.00 each
Driver and/or Passenger Traverse Body Supports
Caged nuts are pre-installed for your convenience.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$115.00 Driver
$115.00 Passenger
Front Outboard Rails, Floor Body Supports
Captured nuts are attached. Top and bottom views are shown in the photo at the right. The support as shown is side interchangeable and is to be used on either the driver or passenger side as was original to the vehicle.
- Die formed in steel heavier than the original.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Driver
$55.00 Passenger
$110.00 Pair
More Information and Add to Cart Options
Inboard Rails, Floor Body Supports
Comes with Captured Nuts are attached.
- Die formed in steel heavier than the original.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Driver
$55.00 Passenger
$110.00 Pair
"Jeep" Stamped Side Repair
The upper edge of our panel is flanged to allow for a flush fit when clamping against your cut along the driver and passenger side entrances.
The Jeep stamped lettering is exact in accordance to our original sample panel and approved by FCA LLC. The forward, upper, rear and lower edges of our panel are a duplication of the original.
- 18 Gauge Steel.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$155.00 Driver
$155.00 Passenger
$310.00 Pair
Lower Side Repair Strip
Our panel is formed with a flanged upper edge that allows for a flush fit for welding purposes. The length of our panel begins with a 900 fold at the front fender seam and ends with a properly formed wheel arch area just like the original.
- Exposed face surface 4" high
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$50.00 Driver
$50.00 Passenger
$100.00 Pair
"Jeep" Stamped Cowl Area Repair Clip
Top, front & bottom edges are formed like the original panel. Rear edge is flanged to form a flush fit during installation.
Includes original type reinforcement on the front of each panel where it bolts to the fender.
To provide for any modifications or variations encountered during installation, we do not pre-drill the mounting holes in the reinforcement.
- 17 1/4" High X 12" Wide
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Driver
$55.00 Passenger
$110.00 Pair
Cowl Body Area Reinforcements
Jeep Cowl Area Reinforcement
- Die Formed
- 14 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$60.00 Driver
$60.00 Passenger
$120.00 Pair
More Information and Add to Cart Options
Cowl Area Reinforcement Lower Repair Section
- Die Formed
- 14 Gauge Steel
- 10 Inches Tall
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$75.00 Driver
$75.00 Passenger
$150.00 Pair
B Pillar, Door Latch Support, Latch Pillar Repair
The lower area of your door latch reinforcement pillar is often rusted away. Our "B" pillar lower repair section may be all that you need for your repair. Our product is well made, properly gauged and has a height of 5" as shown.
- The lower baffel is pre-installed in its proper position.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Driver
$55.00 Passenger
$110.00 Pair
Rear Floor Riser
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$145.00 each
Rear Floor Panel
Strict attention is paid to crisp stamping detail and general panel appearance and accuracy. Our main panel is properly American gauged. Our attached floor supports are over-gauged which will provide you with a much tougher and durable panel.
All appropriate threaded fasteners are attached as they were on the original panel.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$350.00 each
Rear Floor Exhaust Heat Baffel
Note that our panel is shown upside down for illustrative purposes and that the indent detail differs from the original.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$45.00 each
Wheelhouse
This wheelhouse matches the original design on Jeeps from '76-'95.
The notches in the rear of the wheelhouse must be cut by the restorer. This allows a more customizable fit to meet both the varying needs of the late CJ5, CJ7, and YJ, and also any customizations that may have taken place on the Jeep throughtout the years or during restoration.
- 18 Gauge Steel
- Ribs and outboard edges are die formed.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$185.00 Driver
$185.00 Passenger
$370.00 Pair
Wheelhouse Support Baffle
Jeep Wheelhouse Support Baffle. Nicely die formed panel.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$45.00 Driver
$45.00 Passenger
$90.00 Pair
Rear Wheel Arch Opening Repair Panel
Our Jeep rear wheel opening (arch) repair panel has a 2 1/4" exposed face with a 1/2" flanged edge for a flush fit for welding. The wheel side edge is properly rolled inward as was original.
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$115.00 Driver
$115.00 Passenger
$230.00 Pair
Tailgate End Body Support
All tailgate end supports are intended to attach the body to the frame via a body bolt at each end of the support.
All captured nuts brought to original factory size and standard.
We have paid very close attention to quality and detail and thus have an exceptional product for you.
- Can also be ordered for use on types that do not have tailgates.
- Die Formed
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$215.00 each
Rear Frame Crossmember Body Support
Perfectly detailed cut and formed in original gauge steel.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$135.00 each
Jeep License Plate
More Information and Add to Cart Options
Custom Flush Mount Taillights
$80.00 each
$160.00 pair
A Classic Jeep Commercial
Shipping / Ordering Information
USA Orders
All domestic lower 48 USA orders are shipped at a *(minimum of $15.00 on orders $75.00 or less) and *(20% shipping to all orders over $75.00 and under $150.00) and *(10% to all orders of $150.00 or more). When ordering by mail we will accept personal, company or cashiers checks and all major types of credit cards. When ordering via fax all major types of credit cards will be accepted. Be sure to carefully record your card number, expiration date and security code. Top credit card security is strictly maintained by us. Click here for a printable order form. For your fastest service you may order on-line.
Foreign / Alaskan-Hawaiian Orders
Foreign can be placed on-line if we are to ship your order to an address anywhere in the USA. In such cases our standard shipping charges will apply. Orders that are to be shipped to foreign countries, Alaska or Hawaii will require a special shipping quote and are not to be placed on-line. You may simply e-mail us your anticipated order and complete shipping address along with your telephone number. We will then provide you with a shipping quote according to your shipping preference if you have one. We will also provide you with further ordering information at that time. All foreign, Alaskan and Hawaiian orders, once confirmed, are to be placed via credit card only. Click here for a printable order form if needed.
Ordering Option Information
Mail Orders
Classic Enterprises
308 W Stout Street
Rice Lake Wi, 54868
Click Here for printable order form if needed or simply write down your order and your other information on whatever paper you choose.
Direct Telephone Orders or Information
715 234-4677 Call anytime 24/7 with questions or an order.
Secure E-Mail Orders
E-Mail us at Mark@ClassicEnt.com or Click here for printable order form which you can scan and submit via jpg format or simply send your order description to us via a text format.
On-Line Orders
www.ClassicEnt.com For your fastest service.
Main Office Phone # 715 234-4677
WE HOPE THAT YOUR PROJECT GOES WELL - CLASSIC ENTERPRISES
Shipping Policy
Classic Enterprises is a manufacturing facility and factory direct outlet. We do not maintain a large inventory of any one particular item and thus are not always stocked with all of the items which you may need. Non-inventoried items are made to order in the order in which the order was received.
Normal shipping time from our facility is 7 days or less. Sometimes it may take a week longer for certain items. We ship via UPS or FEDEX Ground, which contrary to legend or exaggeration, can take as long as 7 days for delivery. If your order does not arrive within 20 days of order placement, give us a call and we will check the status of your order or furnish you with a tracking number at that time.
Return Policy
Any of our products can be returned for a prompt credit or refund for any reason within 30 days of the receipt of your order. No returns will be accepted without prior approval. All returns must include the original paperwork if available and a detailed note stating the reason for the return. We also will require a clear return address, a telephone number and an e-mail address if available. A 10% restock/transaction fee will be deducted from any standard refund. An additional restock fee will be assessed on any returns that must be re-worked by us in order to be resalable. Any products which have been damaged or modified by the customer will be considered to be non-returnable. Return shipping costs are the responsibility of the customer although we will assume or reimburse all return expenses if we are in error.
Thank you in advance for your patience and consideration.